Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.

Author: Dozshura Grozshura
Country: Philippines
Language: English (Spanish)
Genre: Art
Published (Last): 10 February 2004
Pages: 411
PDF File Size: 8.26 Mb
ePub File Size: 20.19 Mb
ISBN: 635-4-88193-222-3
Downloads: 1601
Price: Free* [*Free Regsitration Required]
Uploader: Mooguran

Page shows with 8 base ports 8 licensed for growth. Should be 8 base ports, which can goto 8 or 16 additional ports. You basically give the same settings for the IBM blade switch but this is a 24 port not a 20 port.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy

This is not true. When you join two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: The autoreconfigure option takes immediate effect at runtime.

You do not need to restart the fcdomain. If a domain is currently isolated due to domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated. If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur. A disruptive reconfiguration may affect data traffic. You can nondisruptively reconfigure the fcdomain by changing the configured domains on the overlapping links and getting rid of the domain overlap.

I am not sure that the statement in bold is correct. Reconfiguration as in changing of domains is always disruptive.


This page incorrect states that fcns reject-duplicate-pwwn is disabled by default.

Testing indicates that this is in fact enabled by default. I am not sure if this is valid.

If you assign port number for physical portshow can you assign for ports ? The default authentication port is This page incorrectly states that you can disable password verification with aaa authentication login none command.

This is not correct as this does not work.

FCIP uses different ports. This can mean several configuration tasks for each iSCSI host. In this case, using the proxy initiator mode simplifies the configuration. Have a few different people read that coniguration I think you will see where I am coming from. Cisco Documentation team has internally re-written this as: This situation can require several configuration tasks for each iSCSI host.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata

If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration. I think what is meant here is: The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite.

Caution The span drop-threshold can be changed only if no span sessions are currently active on the switch. Page Document states: You cannot mix ingress guiide egress interfaces in the same SPAN session. This is not correct. IP routing does not have to be enabled, unless there is a specific topology where IP routing is necessary. It is worded as guixe it is a requirement but it is in fact not. This should be made more clear. I am not sure. These pages talk about an active mode of fcanalyzer.


Although it can be configured it has no effect. There is no information contained 9214 the example given that shows the configuration or enabling of FCIP interfaces. This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator. You must be logged in to post a comment.

Should say Step 1 Enable the mgmt 0 interface. Page Figure shows contiguration ip default-gateway Page States in one bullet: Then states two bullets later: This is very redundant and can be combined into one bullet. Page Information is repeated twice on the same page: Certainly there is either a mistake in the wording or the example. On the same page I find this block of text very vague and confusing: About Configuratioh Message Logging csico configured system message logging server.

Obviously there was a part of this paragraph that got chopped off somewhere.

Leave a Reply Cancel reply You must be logged in to post a comment. This blog is mostly about my pursuits in Data Configuratjon. Previous blog entries also dealt with storage, compute, virtualization and professional services. From time to time I will blog about other things of interest. The opinions expressed in this blog are entirely my own and should not be taken confiburation the opinion of my employer.

Proudly powered by WordPress.

Author: admin