Canon Ir Error Code List. Code Description. E Communication error ( with pedestal). E Communication error (with ASSIST). Free downloads Error Codes Canon iRPage 1 of 5 Error Codes Canon iR Download here the full version of service manual iR Code List. Thank you for purchasing the Canon iR/iR/iR Series Machine. This Manual describes the use of the List of Error Codes Without Messages.
|Published (Last):||14 September 2014|
|PDF File Size:||19.72 Mb|
|ePub File Size:||10.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Main cause The fixing film unit is faulty. The main thermistor has an open circuit. The fixing heater has an open circuit. The main power supply PCB is faulty. Caution To reset errr error, execute the following in service mode: Liet Is the connector of the fixing assembly connected? Fixing film unit thermistor Check the interval between pin 1 and pin 2 and between pin 3 and pin 4 of the connectosr 4-pin of the thermistor for electrical continuity.
The heater has an open circuit, or the thermal switch is open. Replace the fixing film unit. Is the drive voltage of the heater supplied by the connector J8 of the main power supply PCB? The heater drive power supply is faulty.
Replace the main power supply PCB. The thermistor control mechanism is faulty. Main cause The fixing film unit is faulty i. Caution To clear the error, execute the following in service move: Fixing film unit Check the interval between pin 1 and pin 2 and between pin 3 and pin 4 of the connectors 4-pin of the thermistor for electrical continuity.
Is it 0 W short circuit? The thermistor has a short circuit. Is the problem corrected? Main cause The main motor M2 is faulty. Connector Is the connector of the main motor connected?
Main power supply PCB: Replace the main motor. Main cause The fixing motor M19 is faulty. Connector Is the connector of the fixing motor connected? Replace the fixing motor.
Main cause The waste toner case is full. The waste toner case full detection mechanism is soiled. The waste toner sensor is faulty. Caution To clear the error, dispose of the waste toner, and turn off and then on the main power switch. If the error is still indicated after disposing of the waste toner, perform the following: Waste toner case full detection mechanism Remove the waste toner case, and turn off and then on the main power switch.
The waste toner case full detection assembly is soiled with toner. Clean both inside and outside of area A of the waste toner case with alcohol. Make sure that no dirt remains inside and outside the area around the round recess. Main cause The DA unit is faulty. The main controller PCB is faulty.
Connector Is the DA unit connected securely? Replace the main controller PCB. Main ir3030 The horizontal home position sensor is faulty. The horizontal registration motor is faulty.
Canon IR 3300 Error Code List
Connector Are the connectors of the horizontal registration home position sensor and the horizontal registration motor connected? Sensor lever damage and interferenceSensor Is abnormal noise heard from the horizontal registration assembly in keeping with the motor rotation?
The horizontal registration assembly is out of place because of damage to the sensor lever. Replace the sensor lever. The horizontal registration assembly malfunctions because of the presence of foreign matter. Remove the foreign matter. The sensor is faulty and cannot detect home position. The output for primary charging, developing, or transfer has deviated from a specific level of voltage. Main cause The contact has poor connection.
The wiring is faulty. The composite power supply PCB is faulty. Contact Is any of the contacts of the primary charging roller, developing assembly, or transfer charging roller soiled? Or, is there poor contact? Clean the contact, and set it once again. Wiring Is the wiring between the contacts for the following normal: Main cause The wiring is faulty short circuit, open circuit.
The laser scanner unit is faulty. Main cause The wiring is faulty short circuit, open circuit, disconnection. The laser scanner motor M10 is faulty. Connect the connectors securely.
The home position sensor does not go ON when the main power switch is turned on. Main cause The scanner home position sensor PS is faulty. The scanner motor M is faulty. The reader controller PCB is faulty. State Does the scanner operate when the power is turned on? Does the output of the scanner home position sensor change?
Replace the rear controller PCB. Caution When this code occurs, no code is indicated, but the keys are locked.
Canon Ir Error Code List – Copy Care Enterprise
The code may be checked in service kr3300 Replace the reader controller PCB. Main cause The inverter PCB is faulty. Wiring Is the wiring from the scanning lamp to the reader controller PCB cqnon Connect the connector firmly, and correct or replace the wiring. Main cause The scanning lamp is faulty. The rear controller PCB is faulty. Replace the scanning lamp. Main cause The main controller PCB is faulty. Execute the following in service mode: Is the proem corrected?
After executing the service mode, be sure to enter the service mode data newly. After replacement, be sure to enter the service mode data newly. After cannon, be sure to enter the service mode date newly. The wiring is faulty short circuit, open circuit. Check the wiring; if normal, replace the ilst controller PCB.
Any of the following is true in the image processing by the main controller: The image data has a fault. The image processing element of the main controller PCB has a fault. Main cause The image data is faulty. The HDD is faulty. If this error occurs during normal copying or printing, the job in question image data is cleared when the main power switch is turned off and then on again; i. If this error occurs frequently, however, a fault on the main controller PCB is a possibility.
System software Try re-installing the system software. E A fault is detected in the image memory. E A fault is detected in the battery for the image memory. Main cause The HDD is codfs.
Correct the connection and the cable. The fax PCB is faulty. Main cause Any of the printer boards accessories is faulty.