ASTM D3654 PDF

ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.

Author: Kajigis Taugis
Country: Thailand
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 17 May 2017
Pages: 392
PDF File Size: 4.35 Mb
ePub File Size: 6.5 Mb
ISBN: 513-2-28473-992-6
Downloads: 48565
Price: Free* [*Free Regsitration Required]
Uploader: Tojataxe

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Users of this standard are expressly advised that determination of axtm validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Where width or other factors causing high adherence to backing make it impossible to remove the specimen at the prescribed rate, remove it at a rate as close to mm [30 in.

ASTM D The test plate with adhesive specimen is vertically hanged on the stand and its bottom is attached with a standard weight.

ASTM D3654/D3654M – 06(2011)

Use of the Weibull distribution is an acceptable alternative. Measure any slippage that has occurred to the nearest 1 mm [1?

This standard is not included in any packages. As the voice of the U. By navigating on this website, you accept their use.

  AVICENNA JON MCGINNIS PDF

Transport of foodstuffs or medical; warmth or cold Available in compartment simple, double or icebox typify Isothermal boxes icebox for two wheels, scooters, motorcycles typify It is common to test at least? Need more than one copy? For Procedures F and Atm, substitute a?

The razor shall be held in position using side plates. Test specimens should be taken from several rolls of a tape and, whenever possible, among several production runs of a tape. The assessment may be within a roll of tape, between rolls or production lots.

Repeat for a total of three washes with this solvent. The edges for about mm [5 in. Combining values from the two systems will result in non-conformance with the standard. Already Subscribed to this document. The mass of the clamp or hook as described in 5. Link to Active This link will always route to the current Active version of the standard.

The tape must be at a true right angle to the bent Conduct an analysis of the logarithm of the data to determine the desired descriptive or comparative statistics.

China Supplier ASTM D3654 Polymide Tape Lasting Adhesive Test Meter

Wholesalers ads Partners Websites. It may be asstm to mask the exposed adhesive of the free end of the specimen. Precision and Bias You can also visit our FAQ section and see our information section on the risks associated with counterfeiting.

  FUJI FINEPIX S4000 MANUAL PDF

The surface roughness height shall be 50 6 25 nm [2.

For Procedures E, F, and G the amount of slippage in mm [in. Summary of Test Method 3. Warning— All operations with solvents should be conducted in a wellventilated hood. International import and export trade leads board. Subscription pricing is determined by: This test method describes procedures for determining the ability of pressure-sensitive tapes to remain adhered under constant load applied parallel to the surface of the tape and substrate.

Your Alert Profile lists the documents that will be monitored.

ASTM D/DM – 06() – Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes

One company reports that, with care, the between laboratory standard deviation and the residual including within roll 3d654 deviation may be higher or lower than reported here, depending on the tape type and manufacturer. NOTE 4—Discard panels showing stains, discoloration, or many scratches. Some computer programs for data analysis allow the use of right-censored data.

Author: admin