ASTM A Standard Specification for Steel Forgings, General Requirements. to steel forgings under any of the following specifications issued by ASTM. This standard is issued under the fixed designation A/AM; the number . 1 ASTM Standards:3 A/AM Specification for Alloy Steel Forgings for. ASTM A/AMb. Standard Specification for Steel Forgings, General Requirements. standard by ASTM International, 11/01/ View all product details.
|Published (Last):||8 September 2017|
|PDF File Size:||4.97 Mb|
|ePub File Size:||17.17 Mb|
|Price:||Free* [*Free Regsitration Required]|
Such cycles shall be followed by tempering within the temperature limits required by the material speci? The primary melting may incorporate separate degassing or re?
The results of the method used shall conform to the requirements of the product speci? Details of heat and product analyses for the evaluation of chemical composition are thoroughly discussed. It is desirable that two of the specimens will have values of cleavage fracture above the value of n, and two will have values below this level.
After forging, specimens shall be allowed to cool prior to reheating for heat treatment. The last asm version of this historical standard is referenced on www.
The outside diameter may be contoured if required. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Supplementary Requirements S5 or S6, concerning straightening of forgings, may be used. Straightening of Forgings S5.
Blocks shall meet one of the following requirements: Materials shall be produced primarily by either electric-furnace, basic oxygen, vacuum-induction VIMor open-hearth melting process. The reference blocks shall be fabricated in accordance with the procedures of Practice E Historical Version s – view previous versions of standard.
These and other limitations or tests may be performed by agreement between the supplier and purchaser. The longitudinal axis of the specimen shall be parallel to the length of the hub, as shown in Fig.
It is necessary to make this determination to ensure that each Furnace HeatA Weight, tons 25 50 50 B A B element in the official chemistry is represented by proportion to its amount in each individual furnace heat. Ultrasonic Examination from Bore Surface S Cooling Prior to Heat Treatment 7. The primary melting may incorporate separate degassing or refining and may be followed by secondary melting, using electro slag ESR or vacuum arc remelting VAR. The heat analysis of the remelted ingot shall be represented by a weighted average see Annex A2 of the individual chemical analyses for each zone.
Combining values from the two systems may result in non-conformance with the standard.
ASTM A / AM – 10 Standard Specification for Steel Forgings, General Requirements
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Charpy Impact Tests S Tension and hardness tests shall be conducted to evaluate mechanical properties such as the percentage 7a88 elongation and reduction of area.
The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order. Traditionally, forging was performed by a smith using hammer and anvil, though introducing water power in the production and working of iron in the 12th century which allowed the use of large trip hammers or power hammers that exponentially increased the amount and size of iron that could be produced and forged easily.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Heat Analysis for Remelted Ingots S This standard has been approved for use by agencies of the Department of Defense. Siddhagiri Metals and Tubes Manufacturer: Magnetic Particle Examination S We have a large inventory of Stainless Steel Forged Fittings which have high tensile strength and provide excellent resistant to corrosion.
For this purpose, a back re?
ASTM A788 Stainless Steel Forged Fittings Suppliers
Bar coding is an acceptable supplemental identi? When not otherwise de? Steel shall be forged by any of these three classes based on forging temperature: Work Item s – proposed revisions of this standard. Dimensions and Finish Steel Forgings, Alloy, for Carburizing Applications. Such treatments are intended to simulate post-weld or other treatments to which the forgings will be subjected during subsequent fabrication.
Superstrength Alloy Steel Forgings. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Current edition approved Nov. Originally approved in In order for primary deoxidation to occur during vacuum treatment, deoxidizing agents such as aluminum or silicon are not to be added to the melt in any signi?
Test each specimen at a different temperature such that the percentage of shear fracture will be both above and below the value of n, but within a range of Level A P S Heat 0.
ASTM A – 02 Standard Specification for Steel Forgings, General Requirements NO_PDF
The acceptance criteria shall be agreed upon between the purchaser and the producer. This suffix shall not be removed until the material speci? This steel is forged through various process depending upon the temperature at which it is done. The following items shall be reported: Wrought Carbon Steel Wheels.